5 Major Mistakes to Avoid While Working with Power Tools

 If you wish to acquire some construction tools or buy a Billy goat blower or other power tools, then you need to know the best ways to demonstrate extremely dangerous tool practices without risking hurting someone. With a crash test dummy, of course! It’s just not easy to explain stupid techniques using words alone.  

It has been observed that each year, emergency rooms report 120,000 visits due to injuries primarily caused by four tools: table saws, circular saws, nail guns, and utility knives. Adding salt to injury is the 200,000 ER visits for eye injuries, a major percentage of which occur during work around the house. It’s simple to see how we prepared this list of the most dangerous don’ts. It is important whenever you buy tools online or offline and use them 

These common mistakes may cause severe injuries. However, these are only a few examples of things not to do. Remember these suggestions while handling the stuff you obtained from the California Power Tool Store so you don’t become the next statistic. 

1. 
   

2. 1. Never Remove the Blade Guard 

All table saws sold include a blade guard, with an attached splitter. The guard covers the blade, to prevent you from touching it accidentally, and the splitter prevents wood from pinching on the blade and kicking back. You needn’t take them off. The guard may be annoying sometimes. However, it’s better to be disturbed than to lose your fingers. 83 percent of the 35,000 emergency room visits involve contact with the blade. 

Whenever you purchase a table saw, consider spending extra for a quality brand. Buy a saw that stops the blade once the skin touches it. When your blade guard is missing, contact the manufacturer for a replacement.  

Even with a blade guard installed, you must keep your fingers away from the blade. Apply a push stick for rips less than 4 inches wide. When you use your thumb to push the piece and the piece kicks back, you endanger torn ligaments, tendons, and broken bones. Push the cut piece past the blade, turn off the saw, and pause for the blade to stop before retrieving the ripped piece. Never reach near a spinning blade to eliminate a cutoff. 

2. 
   

3. 2. Never Utilize the Table Saw Fence for Crosscuts 

One of the most dangerous table-saw practices is to cut a board to length utilizing the fence as a guide. There’ll be a possibility that the board will be pinched between the blade and the fence and be thrown back into the body with lots of force. This nasty incident is called “kickback.” Cracked ribs, broken thumbs, ruptured spleens, and punctured eyes are only a few of the consequent injuries you may suffer. Nearly 35,000 people end up in the emergency room every year with table-saw injuries, with 10 percent of them hospitalized. According to industry experts, almost half of table saw injuries are caused either directly or indirectly by kickback. 

A few other ways to prevent kickback injuries are as follows: 

• 
  

• Refrain from ripping wet, bowed, or twisted lumber.  
• Don’t cut anything longer than it is wide with the shorter side against the fence.  
• Place your body to the right or left of the miter saw slots, never directly behind the blade. 
• Don’t allow bystanders to walk behind you while operating the saw. 

3. 
   

4. 3. Never Put Your Hands Near a Nail Gun 

You may be a nail gun expert. However, nails always don’t go straight. Wood grain or knots may divert the nail and lead to its shooting out the side of the board. When you drive the nail at an angle to toenail a board, there’s a probability that the nail can glance off and go shooting into space. Grab a board with your free hand, and keep it at a proper distance from the nail gun muzzle. When you reach over a board to hold it down, move your hand out of the nail’s path. Avoid shooting into large knots to deflect the nail. Always wear eye protection while you’re employing a nail gun. 

4. 
   

5. 4. Never Put Your Hand Directly Behind a Circular Saw 

There are approximately 14,000 visits to the emergency room each year due to circular saw injuries. Some of these injuries may lead to lost or severely damaged fingers. While you use a circular saw, check that if the blade binds, the saw can shoot backward quicker than you can move your hand out of the way. Anything in the blade’s way, including your limbs, is in danger of getting cut. Prevent the risk by securing your work and keeping both hands on the saw whenever feasible. Moreover, keep your body to the side of the saw instead of directly behind it. 

5. 
   

6. 5.Never Be Careless with a Knife 

Utility knives are one of the most lethal tools, accounting for a phenomenal figure of 60,000 estimated emergency room visits per year. It takes a single slip to put a deep cut in any body part that’s in the way. Though maximum cuts are superficial, they may only require a few stitches, and permanent tendon as nerve damage is common. 

The most ideal method to prevent an injury is to fix materials whenever possible to prevent any possibility of hand-holding them. If you need to hold something while cutting, there should be a line at right angles to the cutting line, and keep your hand behind it. 

Inference 

It’s imperative to purchase from the best online tool store in California for the authenticity of the tools. However, disastrous mistakes should be avoided under all circumstances.